20 KHz Aluminum Booster 3.25 inch ring for Branson or Dukane

$535.00

Fits all Branson 5170, 501, 8800, 851, 900 series and 2000 series standard actuators, assembly stands, and IW systems, Dukane 43x2xx presses and thrusters, Sonics and Materials E, F, and G systems, and many Ultra Sonic Seal systems. Check mounting ring and stud sizes to be sure.  Input and output threads are 1/2-20.  Adapter studs are available if required.

All-new, precision made in USA. One year limited warranty.

PLEASE SPECIFY GAIN RATIO: 0.4, 0.5, 0.6, 1.0, 1.24, 1.5, 1.75, 2.0, 2.5

Clear selection

Description

These 20KHz aluminum boosters are precision made from certified materials and tuned to tight frequency tolerances for trouble free operation. These boosters are less durable than titanium boosters but have lower mass and higher thermal conductivity so may be preferred in continuous or high duty cycle applications or where low stack mass is desired but are not recommended where frequent stack assembly/disassembly occurs.

They are constructed with a 3.25″ diameter by 0.75″ thick mounting ring set that is made to be disassembled for o-ring replacement.

Input stud is 1/2-20, output thread is 1/2-20.  Order step studs if required to adapt.

All-new precision made in USA.  One year limited warranty.

Additional information

Weight 2.7 lbs
Dimensions 12 x 6 x 5 in
Gain Ratio:

0.4, 0.5, 0.6, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5

You may also like…

20spanner
Spanner Wrench 15/20KHz Hinged Cast
This durable cast steel spanner wrench is of the hinged style. It is appropriately sized to fit most 15 and 20 KHz transducers/converters, boosters, and horns/sonotrodes. Price shown is for one only. In most cases, you will need a pair, so order two. Warranty is one year, one time replace.
not rated $36.00 Add to cart
20TV900
20KHz Stack Vise for Ultrasonic Tooling
This stainless steel stack vise is designed specifically to clamp 20KHz converter front slugs and booster spanner "collars" during assembly or disassembly to reduce damage to expensive ultrasonic stack components. The vise features two clamping chambers, one for tooling 1.5" (25.4 mm) dia. and one for tooling 1.8" (45.7 mm) dia. The two-pin hinge design allows the upper jaw to "float" and seek the best clamp position on the tool for maximum contact. The securing bolt has a long lever handle that can be re-positioned out of the way once secured. The securing bolt can be completely removed so the upper vise jaw can be fully opened. The steel spanner-hole pins are set in stepped holes such that they can be driven out from the bottom of the vise should they ever need replacement.
not rated $380.00 Add to cart
High Pressure Silicone Ultrasonic Stack Grease
The function of grease in the joint is to: 1. Fill the microscopic valleys in the surface of the tooling to improve acoustic transfer from one component to the next. 2. Remain in the joint so the metal of the two pieces of tooling do not become "clad" together by the action of the ultrasound and thus impossible to disassemble. Never use grease and a polymer washer in the same joint.
not rated $1.95 Add to cart
Polymer (Mylar) Washers for Stack Joints (35 pack)
These washers made of heat-resistant Mylar(TM) can be used instead of high pressure silicone grease in ultrasonic stack joints. IMPORTANT: Use a new washer each time the tooling is reassembled. Do not use both grease and a washer in the same joint. Washers come 35 to a pack. Order the number of packs you want, not the number of washers.
not rated $26.50 Select options
ST20STEP
Step Stud 1/2-20 to 3/8-24
This is a specially heat treated steel socket-head stud with 1/2-20 threads on one end and 3/8-24 threads on the other. Used for adapting horns to boosters that do not have the same thread size. No warranty.
not rated $16.00 Add to cart
stud
Horn/Booster Stud for Ultrasonic Tooling
These specially heat-treated steel studs have cup points, and are chemically blackened. No warranty.
not rated $1.95 Select options