Back-to-Back SHV Bulkhead Connector

$35.00

This back-to back SHV connector connects with the standard ultrasound cable-mounted SHV connector to connect through a panel into an enclosure or make another SHV ultrasound cable into an extension cable.

This item comes with all you see in the photo: connector, silicone rubber gasket, lock washer and nut.

Description

 

This back-to back SHV connector connects with the standard ultrasound cable-mounted SHV connector to connect through a panel into an enclosure or make another SHV ultrasound cable into an extension cable.

This item comes with all you see in the photo: connector, silicone rubber gasket, lock washer and nut.

This connector can be mounted in a panel up to 0.341″ (8.6 mm) thick, and here is the hole you will need:

You will also need a 1/2 inch (13 mm) loop terminal connector (not sold by tributek) to ground the body of the connector directly to earth ground in the cabinet.

If using this item to create an extension cable, once the connections are made the entire connection including the connectors on the cables must be shrink-tubed or wrapped with electrical tape to prevent any connector body metal contact with people, machine frame, puddles, etc. The connector outer body is generally grounded by the cable shield, but prudence dictates the extra caution.

Maximum outside diameter at the center flange is 0.69″ (17.5mm) and overall length is 2″ (50.8 mm).

Additional information

Weight .1 lbs
Dimensions 6 x 4 x 1 in

You may also like…

Branson CR-20C Converter Replacement
This aftermarket replacement converter replaces machinery-mounted probe converter CR-20C (125-135-210R), which has a one meter cable and SHV jack used with 20KHz 2000, 2000X, and DCX series power supplies.  Three-year limited warranty.  All-new precision made in the USA (ask Branson where they make theirs) in a climate-controlled ISO-registered facility.
not rated $1,955.00 Add to cart
Polymer (Mylar) Washers for Stack Joints (35 pack)
These washers made of heat-resistant Mylar(TM) can be used instead of high pressure silicone grease in ultrasonic stack joints. IMPORTANT: Use a new washer each time the tooling is reassembled. Do not use both grease and a washer in the same joint. Washers come 35 to a pack. Order the number of packs you want, not the number of washers.
not rated $26.50 Select options
Branson CH-20C Converter Replacement
This aftermarket replacement converter replaces sealed machinery-mounted probe converter CH-20C (159-135-211R), which has a one meter coax cable and SHV jack used with 20KHz 2000, 2000X, and DCX series power supplies.  Three-year limited warranty.  All-new precision made in the USA (ask Branson where they make theirs) in a climate-controlled ISO-registered facility.
not rated $2,035.00 Add to cart
20TV900
20KHz Stack Vise for Ultrasonic Tooling
This stainless steel stack vise is designed specifically to clamp 20KHz converter front slugs and booster spanner "collars" during assembly or disassembly to reduce damage to expensive ultrasonic stack components. The vise features two clamping chambers, one for tooling 1.5" (25.4 mm) dia. and one for tooling 1.8" (45.7 mm) dia. The two-pin hinge design allows the upper jaw to "float" and seek the best clamp position on the tool for maximum contact. The securing bolt has a long lever handle that can be re-positioned out of the way once secured. The securing bolt can be completely removed so the upper vise jaw can be fully opened. The steel spanner-hole pins are set in stepped holes such that they can be driven out from the bottom of the vise should they ever need replacement.
not rated $380.00 Add to cart
20spanner
Spanner Wrench 15/20KHz Hinged Cast
This durable cast steel spanner wrench is of the hinged style. It is appropriately sized to fit most 15 and 20 KHz transducers/converters, boosters, and horns/sonotrodes. Price shown is for one only. In most cases, you will need a pair, so order two. Warranty is one year, one time replace.
not rated $36.00 Add to cart