20KHz Full Wave Water Cooled Booster

$2,375.00

This 20 KHz full wave liquid/water cooled booster assembly provides ultimate stack temperature management.

PLEASE SPECIFY GAIN RATIO: 0.4, 0.5, 0.6, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5

Clear selection

Description

This 20 KHz full wave liquid/water cooled booster assembly provides ultimate stack temperature management.

The standard configuration uses an anodized aluminum input coupler to maximize thermal conduction of heat from the converter/transducer to the cooling liquid. The upper seal is by a single relatively massive o-ring seal utilizing a highly heat- and chemical-resistant o-ring material.

Ports

The assembly comes standard with coolant fittings for 3/8-inch diameter ID tubing, sufficiently large for good coolant flow and sufficiently differentiated from the 1/4-inch OD fittings for cooling air on a typical 20KHz converter/transducer to avoid expensive inadvertent in-plant installation problems.

The cooling ports are offset so as to create a swirling flow in the coolant which improves heat transfer and helps to sweep away incipient cavitation bubbles and prevent cavitiation which could erode the vibrating components or the anodized aluminum cooling chamber sleeve.

A 1/4-NPT thermocouple port opposite the inlet/outlet ports allows easy installation of our type J thermocouple kit, useful both for monitoring actual coolant temperature and for creating a control circuit which would allow coolant flow only when the coolant rises to a certain temperature to avoid situations where a stack could become too cool.

AR System

The lower seal is by means of a conventional booster o-ring mount arrangement that has 12 radial positions available for the anti-rotation feature. This allows the ports on the sleeve to be oriented at 30-degree intervals relative to a non-round horn/sonotrode.

All gain is generated in the output half-wave, which is made of aluminum for its high thermal conductivity and lower cost. Same assembly with titanium output end for maximum durability is model TBW100T.

Overall diameter is 3.25″/82mm (same as standard 20KHz booster mounting ring). Diameter in input nodal area is 2.97″/76mm (same as Branson CR-20/tributek AM44C20R housing). Stud and output threads are 1/2-20.

One year limited warranty. Made in USA. Note that this is a taxable item in Illinois unless you are a tax-exempt purchaser or intend to use this in manufacturing production.

Additional information

Weight 8 lbs
Dimensions 14 x 8 x 6 in

You may also like…

ST20STEP
Step Stud 1/2-20 to 3/8-24
This is a specially heat treated steel socket-head stud with 1/2-20 threads on one end and 3/8-24 threads on the other. Used for adapting horns to boosters that do not have the same thread size. No warranty.
not rated $16.00 Add to cart
High Pressure Silicone Ultrasonic Stack Grease
The function of grease in the joint is to: 1. Fill the microscopic valleys in the surface of the tooling to improve acoustic transfer from one component to the next. 2. Remain in the joint so the metal of the two pieces of tooling do not become "clad" together by the action of the ultrasound and thus impossible to disassemble. Never use grease and a polymer washer in the same joint.
not rated $1.95 Add to cart
Polymer (Mylar) Washers for Stack Joints (35 pack)
These washers made of heat-resistant Mylar(TM) can be used instead of high pressure silicone grease in ultrasonic stack joints. IMPORTANT: Use a new washer each time the tooling is reassembled. Do not use both grease and a washer in the same joint. Washers come 35 to a pack. Order the number of packs you want, not the number of washers.
not rated $26.50 Select options
stud
Horn/Booster Stud for Ultrasonic Tooling
These specially heat-treated steel studs have cup points, and are chemically blackened. No warranty.
not rated $1.95 Select options
20spanner
Spanner Wrench 15/20KHz Hinged Cast
This durable cast steel spanner wrench is of the hinged style. It is appropriately sized to fit most 15 and 20 KHz transducers/converters, boosters, and horns/sonotrodes. Price shown is for one only. In most cases, you will need a pair, so order two. Warranty is one year, one time replace.
not rated $36.00 Add to cart
20TV900
20KHz Stack Vise for Ultrasonic Tooling
This stainless steel stack vise is designed specifically to clamp 20KHz converter front slugs and booster spanner "collars" during assembly or disassembly to reduce damage to expensive ultrasonic stack components. The vise features two clamping chambers, one for tooling 1.5" (25.4 mm) dia. and one for tooling 1.8" (45.7 mm) dia. The two-pin hinge design allows the upper jaw to "float" and seek the best clamp position on the tool for maximum contact. The securing bolt has a long lever handle that can be re-positioned out of the way once secured. The securing bolt can be completely removed so the upper vise jaw can be fully opened. The steel spanner-hole pins are set in stepped holes such that they can be driven out from the bottom of the vise should they ever need replacement.
not rated $380.00 Add to cart