Name: Generator Start Cable for Dukane Ultra Series 2 meter
SKU: USC2MJ20
Availability: InStock

Description

This cable connects to the J20 jack on the rear of any Dukane Ultra series generator. On dry contact closure it provides 24VDC to the driver board and runs ultrasound until the contact opens.

For safety reasons, when using this cable in automation or continuous-ultrasound workstation applications this cable must be connected to NORMALLY OPEN contacts and the relay coil be energized to run ultrasound, so if control voltage is lost in an EMERGENCY STOP or control power supply failure ultrasound will stop. Never connect this cable to manual on/off switch unless it is a momentary type and connected to normally open contacts.

Connector is used, cord is new.

Made In USA

Additional information

Weight	0.5 lbs
Dimensions	6 × 6 × 1 in

20 KHz Aluminum Booster 3.25 inch ring for Branson or Dukane

Fits all Branson 5170, 501, 8800, 851, 900 series and 2000 series standard actuators, assembly stands, and IW systems, Dukane 43x2xx presses and thrusters, Sonics and Materials E, F, and G systems, and many Ultra Sonic Seal systems. Check mounting ring and stud sizes to be sure. Input and output threads are 1/2-20. Adapter studs are available if required. All-new, precision made in USA. One year limited warranty. PLEASE SPECIFY GAIN RATIO: 0.4, 0.5, 0.6, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5

$630.00 Add to cart

Step Stud 1/2-20 to 3/8-24

This is a specially heat treated steel socket-head stud with 1/2-20 threads on one end and 3/8-24 threads on the other. Used for adapting horns to boosters that do not have the same thread size. No warranty.

$22.00 Add to cart

Ultrasound Cable Standard RF Coax SHV-SHV 11 meter

This style of cable is used with most Dukane machines and many Branson machines. Terminated at both ends by SHV connectors and appropriate for use with ultrasonic power supplies/generators up to and including 3000 watts power output. Not for use … Continued

$210.00 Add to cart

High Pressure Silicone Ultrasonic Stack Grease

The function of grease in the joint is to: 1. Fill the microscopic valleys in the surface of the tooling to improve acoustic transfer from one component to the next. 2. Remain in the joint so the metal of the two pieces of tooling do not become "clad" together by the action of the ultrasound and thus impossible to disassemble. Never use grease and a polymer washer in the same joint.

$3.50 Add to cart

Ultrasound Cable Standard RF Coax SHV-SHV 3 meter

$165.00 Add to cart

Spanner Wrench 30/40KHz Hinged Cast

This durable cast steel spanner wrench is of the hinged style. It is appropriately sized to fit most 30 and 40 KHz transducers/converters, boosters, and horns/sonotrodes. Price shown is for one only. In most cases, you will need a pair, so order two. Warranty is one year, one time replace.

$45.00 Add to cart

20 KHz Titanium Booster 3.25 inch ring for Branson or Dukane

$950.00 Add to cart

Dukane 110-3122 Transducer Replacement

Dukane 110-3122 transducer replacement used in almost all 20KHz Ultra Series, DPC, and iQ thruster and press systems that delivers rugged quality and superior value. All-new, precision made in USA in a climate-controlled ISO-registered facility. Three year limited warranty.

$1,890.00 Add to cart

Spanner Wrench 15/20KHz Hinged Cast

This durable cast steel spanner wrench is of the hinged style. It is appropriately sized to fit most 15 and 20 KHz transducers/converters, boosters, and horns/sonotrodes. Price shown is for one only. In most cases, you will need a pair, so order two. Warranty is one year, one time replace.

$45.00 Add to cart

Dukane 41C30 Transducer Replacement

Dukane 41C30 probe transducer replacement used with almost all 20KHz Ultra Series, DPC, and iQ generators that delivers rugged quality and superior value. All-new, precision made in USA in a climate-controlled ISO-registered facility. Three year limited warranty.

$2,180.00 Add to cart

20KHz Stack Vise for Ultrasonic Tooling

This stainless steel stack vise is designed specifically to clamp 20KHz converter front slugs and booster spanner "collars" during assembly or disassembly to reduce damage to expensive ultrasonic stack components. The vise features two clamping chambers, one for tooling 1.5" (38 mm) dia. and one for tooling 1.8" (46 mm) dia. The two-pin hinge design allows the upper jaw to "float" and seek the best clamp position on the tool for maximum contact. The securing bolt has a long lever handle that can be re-positioned out of the way once secured. The securing bolt can be completely removed so the upper vise jaw can be fully opened. The steel spanner-hole pins are set in stepped holes such that they can be driven out from the bottom of the vise should they ever need replacement.

$515.00 Add to cart

Ring Stand Holder for 20KHz Ultrasonic Stacks

This anodized aluminum holder clamps to almost any ring stand and securely holds an ultrasonic stack using a booster having a mounting ring with a diameter of between 2.65" (67 mm) and 3.25" (83 mm), which is most of the standard ones. To mount a stack, set the holder to an appropriate height on the ring stand and simply hang the stack in the holder. Not using a booster? Flip the holder over and use the other side, which is a better fit for converters with diameters between 2.65" (67 mm) and 2.99" (76 mm) which includes almost all 20KHz converters of at least 500 watt power capability.

$240.00 Add to cart

Generator Start Cable for Dukane Ultra Series 2 meter

Description

Additional information